Nest Thermostat Not Working? Fixes for Delayed, Offline and No Heat or Cool

A Nest thermostat not working usually shows you something: a “Delayed” countdown, an offline warning in the app, or a house that stays cold (or hot) while the display says it’s heating or cooling. These look like three different problems, but they often have the same cause. In a lot of homes, the thermostat simply isn’t getting enough steady power.

This guide starts with that power check, then goes through each symptom one at a time. It covers the Nest Thermostat (2020), the Nest Learning Thermostat (3rd and 4th gen) and the Nest Thermostat E. If you have a 1st or 2nd gen Learning thermostat, read the offline step first: Google removed those models from its apps in October 2025. Not sure which one is on your wall? Here’s how to tell which Nest thermostat you have.

Quick Fixes

Try these in order before getting into the details.

  1. Check the battery. Look at the power level on the thermostat (Step 1 shows where). A low battery causes Delayed messages, Wi-Fi drops and a blank screen.
  2. Restart the thermostat. Open Settings on the thermostat and choose Restart. This refreshes its Wi-Fi connection without changing any settings. Our guide on how to reset a Nest thermostat has the steps for every model.
  3. Restart your router. Unplug it for 30 seconds, plug it back in and give it a couple of minutes before you check the app again.
  4. Check the mode and Eco. Make sure the thermostat is in Heat, Cool or Heat•Cool, not Off, and that it isn’t sitting at an Eco Temperature.
  5. Check the breaker and the furnace switch. If the HVAC system has no power, the thermostat can’t run it and can’t charge its battery.
  6. Read the code on the screen. A letter and number like E1 or N260 points straight at the cause. Step 2 explains the common ones.

Why Your Nest Thermostat Stops Working

Every Nest thermostat has a battery for the screen, Wi-Fi and sensors. On the Learning thermostats and the Thermostat E it’s built in and rechargeable. The Nest Thermostat (2020) uses two AAA batteries as backup power instead.

The thermostat needs a steady 24V supply to stay charged. With a C wire (the “common” wire), it gets that power all the time. Without one, it takes small amounts of power through the heating and cooling wires, and on some systems that isn’t enough. The battery runs down, and the thermostat starts saving power in ways that look like other problems.

Google lists these as signs of a power shortage:

  • “Delayed” messages that show up often
  • Wi-Fi that disconnects now and then
  • Heating or cooling that turns on and off in short bursts
  • A fan that runs all the time or won’t turn on
  • A battery that drains quickly, or a screen that won’t turn on
  • Help codes E1, E297, N260, N261, N410 or N411
Nest Thermostat Not Working - diagram showing low power as the common cause of Delayed messages, an offline thermostat and no heat or cooling, with the other causes to check for each

Google also says heat-only, cool-only, zoned and heat pump systems need a C wire or a power accessory. If your home has one of these and your Nest has no C wire, power is the first thing to check. Our guide to Nest thermostat installation explains how the app tests the power during setup.


Nest Thermostat Troubleshooting: Step by Step

Steps 1 and 2 apply to any Nest thermostat not working; Steps 3 to 6 are for a specific problem.

Step 1: Check the Battery and Power

Where you check depends on your model:

ModelBatteryWhere to checkHow to recharge
Nest Learning Thermostat (4th gen)Built-in, rechargeableSettings > Equipment > Power infoUSB-C cable, up to an hour
Nest Thermostat (2020)2 AAA alkalineSettings > battery iconReplace both AAA batteries
Nest Learning (3rd gen) or Thermostat EBuilt-in, rechargeableSettings > Technical Info > PowerMini or micro USB cable

To charge a Learning thermostat or Thermostat E, pull the display off the base and plug it into a wall charger. For the Nest Thermostat (2020), Google asks for good-quality 1.5V AAA alkaline batteries from a known brand.

On the 3rd gen and the Thermostat E, the Power screen shows a voltage. Google says that below 3.8V the thermostat won’t reconnect to Wi-Fi, so a low reading explains an offline thermostat right away.

Charging fixes the symptom for now. If the battery runs low again after a few days, the thermostat needs more power (see the power fix below). Our Nest thermostat battery guide explains each model’s warning lights, battery codes and voltage readings.

Step 2: Read the Help Code

A Nest shows a code when it finds a specific problem. The ones that come up most:

  • E1, E297, N260, N261, N410, N411: not enough power. You need a C wire or the Nest Power Connector.
  • E2 and E5 (and related numbers): a power or heating/cooling wire isn’t detected. Usually a loose wire.
  • W1 to W5 and TD codes: Wi-Fi problems.
  • E10, N254 and similar: no power to the Y1 (cooling) wire, often because a safety cutoff on the HVAC system has tripped.

For any other code, check Google’s Nest thermostat help codes page.

Step 3: If Your Nest Thermostat Says Delayed

A Nest thermostat delayed message means one of two things, and it’s easy to tell them apart.

The first is normal. To protect the compressor in an air conditioner or heat pump, Nest waits a minimum amount of time between cycles (Google calls it compressor lockout time). If the system just turned off and you ask for heat or cooling again, you’ll see a short countdown, something like “Heating is delayed for 2:30 mins”. When the countdown ends, the system starts. That’s the thermostat working as designed, and there’s nothing to fix.

The second is a power problem. If Delayed appears again and again, the countdown repeats without the system ever running, or you see it on most cycles, the thermostat doesn’t have enough power to switch your system on reliably. Google lists frequent Delayed messages as a sign of a power shortage. Charge the battery as a short-term fix (Step 1), then add a C wire or a Power Connector.

Nest Thermostat Not Working - diagram comparing a normal Delayed countdown that ends and starts the system with a repeating countdown caused by low power

Step 4: If Your Nest Thermostat Is Offline

A Nest thermostat offline in the Google Home app (or the Nest app) has lost its internet connection. It usually keeps heating and cooling on its schedule, so you have time. Follow Google’s order:

  1. Check the battery first (Step 1). A low battery can switch the Wi-Fi off, and no router change will fix that.
  2. Update the app and check that another device can get online on the same Wi-Fi.
  3. Restart the router, then the thermostat.
  4. Check the signal on the thermostat’s Network screen. If it’s weak, a closer router or a mesh point helps.
  5. Try your phone’s hotspot. If the thermostat connects to the hotspot but not your Wi-Fi, the problem is in your router settings.
  6. Reconnect it to Wi-Fi from the thermostat’s network settings, with your Wi-Fi password.

If you need to look at the router, Google recommends keeping the 2.4 GHz band on, giving the 2.4 and 5 GHz bands different names if they’re set up separately, keeping multicast on and wireless isolation off, and setting the DHCP lease time to at least 2 hours. Strict firewall or parental control settings can also block the thermostat from Google’s servers. Networks with a login page (like hotels) and business networks with individual logins don’t work at all.

Sometimes nothing is wrong in your home: Google’s Nest service has had outages where thermostats showed offline while home Wi-Fi worked fine. If other people are reporting the same problem online, wait it out. If your Nest cameras or doorbell are offline too, our Nest camera troubleshooting guide covers the camera-specific checks.

If you have a Nest Learning Thermostat 1st or 2nd gen, it was removed from the Google Home and Nest apps on October 25, 2025. It still heats and cools, and you can still change it on the device, but it won’t come back online. If you want app control again, see our best smart thermostats for a replacement.

Step 5: If There’s No Heat

Start with the settings, then the wiring:

  • Check the mode and the target temperature. The thermostat must be in Heat or Heat•Cool, with the target above the room temperature.
  • Check for Eco. Home/Away Assist and presence automations can switch the thermostat to an Eco Temperature when they think you’re out. If it keeps happening while you’re home, turn off automatic Eco in Home/Away Assist. Our guide to Nest Eco mode shows where that setting is in the Google Home app and how to turn Eco off on each model.
  • Run a system test. On the Nest Thermostat and Learning 4th gen, use the Mode screen in the Google Home app; on the 3rd gen and Thermostat E, go to Settings > Equipment > Test. If the furnace doesn’t respond, the thermostat has done its part. Our guide to fixing a thermostat not turning on heat covers what to check at the furnace.
  • Check the wires. Turn off power at the breaker, pull the display off and make sure each wire is pushed fully into its connector with about 3/8 inch of clean copper showing.
  • Check the furnace. A tripped breaker or an open furnace door switch cuts power to the whole system.

If you have a heat pump and it blows cold air in Heat mode (and warm air in Cool), the O/B setting is the wrong way round. Google’s fix is to switch it from O to B, or from B to O, in the thermostat’s heat pump settings. Our guide to the best thermostats for heat pumps explains these settings in more detail.

Step 6: If Your Nest Thermostat Is Not Cooling

With a Nest thermostat not cooling, check Step 3 first: a short countdown after the AC turns off is normal. Then look at these:

  • Airwave. This feature turns the compressor off a little before the target temperature and runs only the fan for the rest of the cycle. The vents keep blowing, but the air isn’t as cold, which can feel like the AC stopped working. You can turn it off in Settings > Temperature Preferences > Airwave.
  • A tripped condensate switch. Many air conditioners have a float switch that cuts the cooling circuit when the drain line backs up, to prevent water damage. Your Nest reports it as no power to the Y1 wire (a code like E10 or N254). Clearing the clogged drain line usually brings the AC back.
  • A compressor alert. Since June 2026, Nest thermostats can warn you about compressor problems with messages like “A/C not cooling. There’s an issue with your compressor.” That points to the equipment, not the thermostat.

Fix the Power Problem for Good

If your Nest keeps running low on power, you have two real options.

The first is a C wire. Many homes already have a spare wire tucked behind the thermostat or in the cable bundle. If the same wire is connected to the C terminal on your furnace or air handler, you can connect the other end to the C connector on your Nest. Our guide on how to install a smart thermostat shows how to check and label the wires safely.

The second is the Nest Power Connector, Google’s own power accessory. It works with the Nest Thermostat (2020), Nest Thermostat E and Learning 3rd and 4th gen, installs at the furnace or air handler and needs a 24V system. Google warns that third-party C-wire adapters can cause problems or damage with a Nest, so the Power Connector is the safer choice. Our C-wire adapter guide compares it with the other options.


When to Call an HVAC Pro

Call a technician if:

  • The thermostat shows a compressor alert, or the system test runs but the equipment doesn’t respond.
  • The Y1 safety cutoff keeps tripping after you clear the drain.
  • Your system is millivolt, high voltage or proprietary. Google lists these as incompatible with Nest.

The Bottom Line

A Nest thermostat not working usually comes down to power, Wi-Fi or a setting. Check the battery first, because low power can cause all three symptoms. A single short Delayed countdown is normal, while a repeating one means the thermostat needs more power. If the battery keeps running low, a C wire or the Nest Power Connector is the fix that lasts.

Why does my Nest thermostat say Delayed?

A single short countdown after your AC or heat pump turns off is normal: Nest waits a minimum time between cycles to protect the compressor. If Delayed appears often or keeps repeating without the system running, the thermostat doesn’t have enough power. Charge the battery, then add a C wire or the Nest Power Connector.

Why does my Nest thermostat keep going offline?

The most common reasons are a low battery, a weak Wi-Fi signal or a router setting. On the Nest Learning 3rd gen and Thermostat E, Google says the thermostat won’t reconnect to Wi-Fi below 3.8V, so check the battery first. Then restart the router and the thermostat and reconnect it to Wi-Fi.

How do I reset my Nest thermostat?

For most problems you only need a restart, which keeps all your settings. Open Settings on the thermostat and choose Restart (on the 3rd gen and Thermostat E, Restart is inside the Reset menu). A full factory reset erases your schedule and settings, so keep it as a last resort.

Does a Nest thermostat need a C wire?

Not always, but Google says heat-only, cool-only, zoned and heat pump systems need a C wire or a power accessory. Any Nest that keeps showing low battery, Delayed messages or power codes like E1 or N260 needs one too. The Nest Power Connector is an option if you don’t have a spare wire.

Do old Nest thermostats still work?

Yes, on the wall. The Nest Learning Thermostat 1st and 2nd gen were removed from the Google Home and Nest apps on October 25, 2025, but they still heat and cool and you can change the temperature and schedule on the device. They can’t be controlled from your phone anymore.

Evan Mercer, founder and lead researcher at Smart Home Matrix

Written by Evan Mercer

Founder & Lead Researcher, Smart Home Matrix

Evan digs through spec sheets, firmware changelogs, and thousands of owner reviews so you don’t have to. Every guide starts with a compatibility check and ends with picks he would install in his own home. Read more about Evan and this site, or see exactly how we choose products.